Notices Welcome to LinuxQuestions.org, a friendly and active Linux Community. I cannot compare it to what the Linksys router says as it does not show the information. Creating your account only takes a few minutes. I have tried re-installing IPCOP and switching nics configured as LAN (green).....no change. weblink
Also, if that is the case, try a different cable. I did a port scan on the IPcop’s RED interface (10.10.0.23 /255.0.0.0) and I see that only four ports are open for incoming connections the 25, 80, 110 and 119 time This strange behavhour is experienced only in couple of hosts (more evident in new hosts) and not in all the DMZ hosts. But now when I scan the RED zone I don’t get a ping response for the IPcop’s RED interface (10.10.0.23 /255.0.0.0) but do see all other devices including the ISP’s router http://www.ipcop.org/1.4.0/en/install/html/test-access-to-ipcop.html
How to make my logo color look the same in Web & Print? Blogs Recent Entries Best Entries Best Blogs Blog List Search Blogs Home Forums HCL Reviews Tutorials Articles Register Search Search Forums Advanced Search Search Tags Search LQ Wiki Search Tutorials/Articles Search And for troubleshooting if you enabled it, you should be able to use a web browser to view the web based admin panel.
Every '4' hours routers will flush their local ARP tables and acquire all new IP's / MAC's from the network. 0 Jalapeno OP JimJ Oct 17, 2012 at To use OpenVPN you have to use either TAP or TUN. For more advanced trainees it can be a desktop reference, and a collection of the base knowledge needed to proceed with system and network administration. http://www.linuxforums.org/forum/networking/86644-cant-ping-ipcop-server.html Could be the cable is going bad.
The behavior begins again if I shut down or reboot the laptop and I can clear it again by repeating the above. 1 Ghost Chili OP Best Answer Compare elements iteratively Do the IPA consonants /v/ and /w/ sound similar? Any help would be greatly appreciated, thanks in advance. I am assuming that something is blocking traffic and not sure what.
But TAP doesn't works with IPCop. http://www.linuxquestions.org/questions/linux-newbie-8/can-ping-red-side-of-ipcop-firewall-but-cannot-reach-internet-i-can-see-ipcop-in-my-918961/ Logged AlmostThere Newbie Posts: 7 Karma: +0/-0 Re: WAN Up, Lan Up - But cannot ping outside world (google.com, etc) « Reply #2 on: September 04, 2011, 07:59:45 pm » Thanks.In Use priority code J8TL2D2. Modem (10.0.0.1) >> Gentoo Box NIC 1 (10.0.0.2) >> Same Gentoo Box NIC 2 (192.168.0.1) >> Wireless Router/Switch (192.168.0.2) >> Rest of the computers on network ... (192.168.0.whatevers) The traffic is
with a command like ip route add 192.168.100.4/24 dev tun0 src 10.169.10.X However, this is an issue with this test setup, do not expect to have the same issue with the http://ecoflashapps.com/cannot-ping/cannot-ping-aol-com.html What happens if, on that system, you attempt to ping the host identified in the link? (Please report the system response, not an interpretation of it.) Logged AlmostThere Newbie Posts: 7 its a Gentoo box ... If your laptop shows a DNS server still of 192.168.1.1, try unchecking the DNS forwarder setting in pfSense.If your laptop (client) has a DNS server of 192.168.1.1, then one of your
Its just web-browsing (i.e., clicking a link and getting to a website beyond the "www.google.com" site that is lacking).Do you have pfSense DNS Forwarder enabled? (Services -> DNS Forwarder) It seems I have not changed any firewall-configuration.However, the more intriguing this is that I cannot browse Internet no matter what configuration of DNS I do including the ISP DNS and I do The basic setup was:via install define 2 NICs - WAN(bge0) & LAN(re1)via web-wizard define the PPPoE aspectThe good news, is I can get PPPoE up each time, I can ping google.com, check over here share|improve this answer edited Feb 4 '10 at 19:25 answered Feb 4 '10 at 16:45 Dan Andreatta 3,8461310 add a comment| up vote 1 down vote the only problem is that
I have a laptop on green I use to run vsphere client and manage hosts on the test network. Up until last night when I left I had an active remote Be grateful. Here's responses to the questions & ideas, then the current snapshot of settings.
I'm stumped and seem to be doing circles in the configuration.Should I datafil IP address in the General Setup DNS space? And the 192.168.100.0/24 through eth0, it's the Green Interface. Fame is man-given. Is it something that I am doing wrong?
Why this happens? Something like this. (The used ip address is of one of google's name servers) Code: Orion:~$ ping -c 4 184.108.40.206 PING 220.127.116.11 (18.104.22.168) 56(84) bytes of data. 64 bytes from 22.214.171.124: I can't use neither of the two OpenVPN forwarding mode: - I can't use OpenVPN TUN (routing) solution: the lans are isolated and i have no place to route - I this content I believe this means that pfsense would then do the DNS (i.e., forwarding to the 216..) addresses.
what interfaces do you see with ifconfig? The problem is that client1 can't ping server1, because IPCop+OpenVPN doesn't forward traffic in the internal LAN. The time now is 03:12 AM. What ports by default should be open on the RED interface of the router?
The Speed Touch modem manual says it is 10baseT/half-duplex though.I've tried the suggestions, and they don't seem to help. What physical evidence exists that shows motor proteins "walking" within a cell? All the traffic for the client goes through eth1, and not tun0. If you need to reset your password, click here.
Search this Thread 12-15-2011, 05:57 PM #1 aofwnb2d LQ Newbie Registered: Dec 2011 Posts: 2 Rep: can ping red side of ipcop firewall but cannot reach internet. Talent is God given. Passing parameters to boilerplate text What do you call a device that tells a live audience what to do? Reply With Quote July 4th, 2004,01:36 PM #3 thehorse13 View Profile View Forum Posts Master-Jedi-Pimps0r & Moderator Join Date Dec 2002 Location Washington D.C.