Home > Cannot Ping > Cannot Ping Wrt54g2

Cannot Ping Wrt54g2

But all hope is not yet lost. The external IP can be dynamic and your ROUTER set in the gateway mode manages it automatically for you. Set Wireless Setup.Domain Name = Blank (unless you have a reason to enter it) 12. It is during this fleeting moment that you may be able to “catch” the router while still momentarily conscious, just before its brain-dead firmware is loaded. weblink

You have to enable Remote Router Access on the client WRT54G. I love these forums!Click to expand... lio256, Apr 9, 2005 #27 shah Network Guru Member joebloggs said: Regarding A1, can you run a wire from that one port to another wireless router and thus be able to Click on Save Settings button. https://community.linksys.com/t5/Wireless-Routers/unable-to-ping-WRT54G2-router/td-p/683773

My TiVo has internet access (it's connected to the BRIDGE WRT54G). Al carrera206, Mar 22, 2005 #12 shah Network Guru Member vizenmaster said: my computer setting like this modem--netgear(192.168.0.1)--wifi--- linksys wrt(192.168.0.2)--pc1(192.168.1.100) laptop(192.168.0.3)--wifi--netgear router this is what i did on my netgear Oh yes, one more thing...

Cheers SHAH shah, Mar 17, 2005 #5 bischen Network Guru Member hello shah, i have 2 problems/questions about your guide. 1. Set Wireless Security.Security Mode = WEP 3. The power light will tell you nothing now. I have a feeling you didn't follow the instructions down to every detail/step.

As i mentioned before I have www-access on my xbox and it´s on a different subnet than the router. Regardless, if you resolve the issue please post back what the problem was so I can improve the guide. We are wondering if someone else initially purchased the refurb item and later returned it to the affiliate we purchased it from, who in turn resold it to us as if Thanks.

If one supplier has delayed your project schedule should the other suppliers on the project be alerted to the new timeline? Why there are no approximation algorithms for SAT and other decision problems? Cheers SHAH shah, Mar 23, 2005 #14 carrera206 Network Guru Member Re: Step by step guide to setup a WRT54G in client bridge mo Shah- Thanks so much for your I'm having trouble setting it up with WPA.

Don't worry about the power light. It could have been buggy firmware itself. This conflict in Cisco's serial number database, caused us a bit of a hassle in getting technical support and the warranty honored until we provided them the Amazon receipt # (to Do I need to choose client-bridged or client-routed to get this to work? 3.

I have read your post many times and tried to enable client mode but it wouldnt work. have a peek at these guys Board index The team • Delete all board cookies • All times are UTC - 5 hours [ DST ] Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group Home Additionally a RAP cannot ping the CLIENT at either address or any CAP. I have also enable the upnp function on the 2 wrt54g (just in case ..).

So after that, I flashed my WRT54g2 v1 with "VxWorksKiller-G2V1-new.bin" via http: 192.168.10.1. Notice that after this configuration, your CLIENT bridge/router has a different IP address for administration. I forwarded the subnet broadcast x.x.x.255 and BINGO! check over here In your post above you mention that 192.168.2.255 should be forwarded to 192.168.1.1, with subnet mask of 255.255.255.255.

CLIENT setup step 4: These steps are temporary so that you don't run into any issues during setup. See below. Set Wireless Setup.Internet IP Address = 192.168.1.2 (or whatever ip address you identified in step 2 of preperation) 4.

Set Wireless Network.Wireless Network Name (SSID) = SUBSTITUTE_YOUR_ROUTER_SSID 5.

CLIENT setup step 1: 1. I want to mimic the following article: http://www.pbs.org/cringely/pulpit/pulpit20050414.html I have all components just cant get the WRT's to connect to the AP's. Jump to the next section. carrera206, Mar 24, 2005 #15 shah Network Guru Member Re: Step by step guide to setup a WRT54G in client bridge mo The symptoms of my problem are that with my

hotrat, May 26, 2005 #53 hotrat Network Guru Member anyone????? Gentle Recoveries If you could simply reflash your seemingly dead router with an official Linksys firmware, you could, like Cher, turn back time. Thank you. http://ecoflashapps.com/cannot-ping/cannot-ping-aol-com.html Trust me, none of the issues that some users have run into have to do with the 2 subnets.

rdjager, May 21, 2005 #47 Lampei Network Guru Member Re: Will this setup work with Talisman? I have set up a static route on the router to 1 of my CAPs of which I know the address as follows: Destination IP Address: 192.168.2.100 IP Subnet Mask: 255.255.255.0 I have disable all the firewall (on the 2 wrt54g), but also on the PC. So now 192.168.1.2 is your ROUTER facing IP and 192.168.2.2 is your CLIENT network facing IP. 14.