Home > Cannot Ping > Network Troubleshooting Steps

Network Troubleshooting Steps

Contents

Thanks. This incident will be reported If one supplier has delayed your project schedule should the other suppliers on the project be alerted to the new timeline? Edited Aug 9, 2013 at 5:47 UTC 0 Poblano OP GP Tech Aug 10, 2013 at 3:00 UTC what alex3031 mentioned should work too what i meant was You could have a bad wireless card. weblink

Proffitt Forum moderator / January 4, 2007 6:18 AM PST In reply to: More info I was afraid of that. I can ... by R. So I got a bit of work done this morning, then tried tackling the sudo su bit...Trying to boot with Linux CD, and now for the life of me, I can't http://www.techrepublic.com/forums/discussions/network-device-using-ip-but-cant-ping-it-help/

Network Troubleshooting Steps

Manually set you IP address to something like 192.168.11.10 I noticed that the DNS servers list only displays your router's address. gusgizmo Ars Tribunus Militum Tribus: Kailua Kona, Hawaii Registered: Aug 26, 2004Posts: 2366 Posted: Sun Nov 04, 2012 2:13 pm Get the mcafee removal tool, I've seen similar issues before after Please. Hmmm Flag Permalink This was helpful (0) Collapse - Since you are behind a router...

If the router's address appears at all, same thing. If you receive Request timed out, make sure router is up and configured properly with correct IP, subnet mask, DHCP and other network settings. Reset Post Submit Post Software Forums Software · 43,584 discussions Open Source · 249 discussions Web Development · 11,536 discussions Browser · 1,205 discussions Mobile Apps · 47 discussions Latest From How To Ping Network Card You assign static IP's but you don't document it in a spreadsheet as to What is assigned and to what kind of device?

On Mac or Linux computers, a similar message will normally appear on screen.Resolving IP Address ConflictsTry the following remedies for IP conflicts:1. Basic Network Troubleshooting Interview Questions Router cannot ping troublesome computer. The wlan0 is the one that will need to be used when communicating with the gateway/router (at 192.168.1.1) to exit to the internet. If so, then the connection to your router's working as well.

Nothing works just out of the box. :( You have to setup the router and then the TCP settings for each PC you have in your home network. Destination Host Unreachable by R. All computers run with ZoneAlarm.My main computer cannot be pinged, yet can ping the other computers fine. Determine the routers address Using the ipconfig command (or ifconfig command for Linux), determine the router's address by looking at the Gateway address.

Basic Network Troubleshooting Interview Questions

What range is the IP subnet that you can't find? Try again by using other network cards. Network Troubleshooting Steps Unix & Linux Stack Exchange works best with JavaScript enabled Connect with us facebook twitter CNET Reviews Top Categories CNET 100 Appliances Audio Cameras Cars Desktops Drones Headphones Laptops Networking Phones Ping Request Timed Out Fix Tuesday, June 08, 2010 8:04 PM Reply | Quote 0 Sign in to vote Hello Mike, "Destination Host Unreachable" is an indication that the computer does not have the information needed

If the computer is holding a current IP address, type 'cmd' (without the quotes) in the text box that appears. have a peek at these guys Unplug the power to your router and cable modem or DSL modem. Connect to the router If all of the above steps have been checked, and your network has a router, make sure the computer can connect to the router by performing the I'm proceeding as if this was accomplished.I also dropped a hint about home made cables which drew no response so I take it the cable was not home mode and has Ping Request Timed Out Solution

Tuesday, June 08, 2010 7:37 PM Reply | Quote 0 Sign in to vote You shouldn't need to install anything for IPv4, it's built-in and your ipconfig output shows it's working. Manually set “IP address” (For example, if your router IP address is 192.168.1.1, we can type the IP address as 192.168.1.22. anywhere on the network? check over here from the server, but is unreachable by any other computer in the LAN. –Dario Fumagalli Jul 29 '13 at 21:32 This is odd.

Yo must have done something? Cannot Ping Computer On Same Network Local time:07:14 PM Posted 03 February 2014 - 04:33 PM See if this helps. Not the answer you're looking for?

Renew the IP on both computers.

no machines are assigned IPs below 25 besides servers and I only have 4. 0Votes Share Flag Collapse - Try these out to see if they cure your issues..... c. If you receive Reply from 127.0.0.1, it works. Ping Transmit Failed General Failure Flag Permalink This was helpful (0) Collapse - just curious...

ping 192.168.1.1 If you get replies back from the router, the connection between your router and computer are good, and you can skip to the next step. Open the Windows command line. Ping Command - How to test Network Adapter Started by Scoop8 , Feb 03 2014 04:06 PM Please log in to reply 4 replies to this topic #1 Scoop8 Scoop8 Members this content Pingable PC #1: IP: 192.168.1.104 Subnet: 255.255.255.0 Default Gateway: 192.168.1.1Pingable PC #2: IP: 192.168.1.95 Subnet: 255.255.255.0 Default Gateway: 192.168.1.1Unpingable PC: IP: 192.168.1.110 Subnet: 255.255.255.0 Default Gateway: 192.168.1.1No, I did not know

Hyper Derivative definition. If you have a wireless network and followed the above steps, but cannot ping the router, turn the computer off again and connect the computer to the router using a network I am not sure why networking folks would know that. BobTheFourth "Formerly connection|interrupted" Ars Praefectus Tribus: Hickory, NC Registered: Feb 3, 2000Posts: 5331 Posted: Sun Nov 04, 2012 7:43 am Sterling_Aug wrote:Have you scanned for a virus/spyware yet?It had McAfee Internet

I'll have to check out the ping after I get back from taking the young'uns to the dentist. networking ssh ping route share|improve this question edited Jul 29 '13 at 20:16 slm♦ 168k42309481 asked Jul 29 '13 at 20:06 Dario Fumagalli 11613 How about putting eth0 and If we have ever helped you in the past, please consider helping us. by R.

All rights reserved. In those situations, I'll tracert machinename and find the ip address that the DHCP is translating. If I disable the nic 2 with the ip address of 192.168.0.3 everything works fine.