Reply Link Bruce Mincks November 14, 2007, 12:24 amI need to fix my swap partition, apparently. One user had a cable blocking the fan; it did not affect ext2, but it wasn't until he fixed the cable-fan problem that ReiserFS worked.) Can I use ReiserFS on other Where does this get written to? Related 4Unable to mount raid on my NAS, trying to rescue the data, how should I proceed?0Device mounted read/write, but can't delete files2Unable to change permissions of file system root1What could Check This Out
Please be sure that you copy it from (or tar it from) a reiserfs partition so that files are created in reiserfs readdir() order as this will improve performance. These other file systems perform poorly because they use a linear search algorithm to find and replace entries in a directory. On the reboot the /dev/md4 couldn't mount and now my configuration is invalid. having open files) on my laptop, does ReiserFS access the disk every 5 seconds?
The reason these patches were not included into 2.4 kernel branch is because they implement new quota format and need new quota code too, which is too big of a change Use the stock go file (boot(flash)/config/go).#!/bin/bash# Start the Management Utility/usr/local/sbin/emhttpThe following line is not stock; but it makes safemode work with go file additions.if grep -wq unraidsafemode /proc/cmdline ; then exit Example given below:/dev/evms/container_1/rvol1 on /mnt/vol1 type reiserfs (ro)6. Introduction to Linux - A Hands on Guide This guide was created as an overview of the Linux Operating System, geared toward new users as an exploration tour and getting started
Path to folder: /etc/foo/bar I need remount /bar folder. Or perhaps making a new folder and mounting it there (just to see what happens). If they are system files (for another Linux distribution for example) DON'T DO THE FOLLOWING. Linux Reader Mount fails after reiserfsck --rebuild-tree failure When reiserfsck --rebuild-tree is run, the first thing it does is to set the root inode value to -1.
Starting with linux kernel v2.4.21 I cannot mount my FS anymore. Ext2fsd For now, most of the documentation is just a snapshot of the old Namesys site (archive.org, 2007-09-29). The following messages mean you have a noisy IDE cable, or it is just too low quality for choosen UDMA mode. http://www.linuxquestions.org/questions/linux-newbie-8/mount-read-and-write-reiserfs-and-ext3-partitions-431032/ My conclusion is that by default/design, only root can write to a native linux partition and root must create a directory(s) and set user permissions to permit ordinary users access.
No, definitely not. Ext2 Volume Manager If you want ReiserFS to outperform any other filesystem in your setup here is one solution: Copy the entire directory that you are not satisfied with to the same partition but Now how are the permissions on each mounting point: ~$ ls -ld /var/local /tmp drwxrwxrwt 20 root root 744 abr 29 17:00 /tmp/ drwxr-x-w They fixed the compiler and thereby allowed the correctly compiled ReiserFS to work.
Traditional file systems typically have poor performance when there are many files in a single directory, but not ReiserFS. http://ecoflashapps.com/windows-10/windows-help-program-winhlp32-exe-for-windows-10.html The key to keeping performance up is to make it easy for the FS to do as much as possible before the fsync() call. smiley_lauf View Public Profile View LQ Blog View Review Entries View HCL Entries Find More Posts by smiley_lauf 04-02-2006, 09:36 PM #13 gilead Senior Member Registered: Dec 2005 Location: with reiserfs. Ext2fsd Windows 10
Your method works fine. The second HDD busy light is flashing endlessly, none of the other HDD are flaashing. Also other Deskstar drives are seem to be a not very good choice. http://ecoflashapps.com/windows-10/windows-system-image-manager-cannot-obtain-read-write-access-windows-10.html The Seatools should have pointed out bad sectors and if you just pull the SMART data from the disk it will indicate if there are bad sectors (they will be listed
The filesystem is read-only. Ext4 Windows 10 You try to run "reiserfsck" on the device and it gives you write permissions error as given below:Partition /dev/evms/container_1/rvol1 is mounted with write permissions, cannot check it Resolution 1. The next sync() writes this atime update, then sync(1) gets updated again.
Blogs Recent Entries Best Entries Best Blogs Blog List Search Blogs Home Forums HCL Reviews Tutorials Articles Register Search Search Forums Advanced Search Search Tags Search LQ Wiki Search Tutorials/Articles Search I'm pretty sure umask is only for vfat partitions thus the error. 0 Back to top MultiQuote Reply #7 bvc root Group: Platinum Posts: 8,682 Joined: 19-September 02 Posted 29 If your read-only mount point is /foo /bar /baz then mount -o rw,remount /foo will keep other mount points read only. Ext2explore Then when I try to rebuild the superblock, it starts asking me all these questions I'm not sure about, and I don't want to lose two months of work here.I'll be
Either way I'm very concerned about losing data since I have many important files on my unraid system. And rfstools just sucks; it balks when the filesystem is not whole and intact. Do LFS, devfsd, and init scripts by hand and you'll be sending mandrake a thank you check in the mail :wink: Heck....I haven't booted to Slack in 2 weeks...aru I'm not. navigate here mkreiserfs created a filesystem that has the wrong notion of how large the partition it is on is.
A fix for this is evolving; the later your ReiserFS patch, the better we handle this. Any caveats?